Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 82 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 82

Test Setup - Test Applications

72

88000 Series

RFC 6349

RFC 6349

RFC 6349 is used to confirm that the Ethernet service is able to properly
carry TCP traffic.

The

RFC 6349

test has to be executed in conjunction with a remote

compatible unit in RFC 6349

Dual Test Set

or

EXFO|Worx Interop

operation mode allowing bidirectional testing. The test provides
independent results for each test direction. The results from
local-to-remote and remote-to-local are available on the local testing unit.



Typical RFC 6349 test application:



Supported Interfaces/Rates: 10M to 10G LAN, 40G, and 100G.

EVC

Testing Unit

Remote Unit

EXFO Unit

EXFO Unit

including BV Units

«
...
80
81
82
83
84
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands