EXFO Power Blazer 88200NGE User Manual Download Page 419

Page: 419 / 887

Test Results

Power Blazer

409

Alarms/Errors Overview

Errors

The following errors are available with 200/400G:



66B Block

: Invalid 64b/66b block code are received. An invalid 64b/66b block

is declared when the synchronization field has a value of 00 or 11.



FEC-UNCOR-CW

(Available when RS-FEC is enabled)

: FEC uncorrectable codeword error is detected on the Ethernet

signal.



FEC-COR-CW

(Available when RS-FEC is enabled)

: FEC correctable codeword error is detected on the Ethernet signal.

The

FEC-COR-CW

does not raise an error, only the count and rate

values are reported.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands