manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 376

Test Setup - Test Configurator, Timer, and System

366

88000 Series

TCP Throughput

TCP Throughput Configuration

Note:

TCP Throughput Configuration is only available on the local unit. 

Initial Window Size

1

 is the window size that is used when the test is 

started: 

1024

 Bytes to 

65536

 KBytes (default is 

2

 KBytes). The Initial 

Window Size value must be between the 

Minimum Window Size

 and 

the 

Maximum Window Size

 values. 

Minimum Window Size

1

 is the minimum window size used for the 

test: 

1024

 Bytes to 

65536

 KBytes (default is 

1

 KBytes). 

Maximum Window Size

1

 is the maximum window size used for the 

test: 

1024

 Bytes to 

65536

 KBytes (default is 

64

 MBytes). 

Rate Unit

 allows selecting the unit that will be used to set the 

Throughput Pass/Fail Verdict Threshold and throughput results: 

%

(default) or 

MBit/s

. 

Throughput Pass/Fail Verdict

 check box when selected (default) 

enables the throughput verdict. 

Threshold

 allows setting the pass/fail verdict threshold value: 

0

to

100 %

(default). 

Restore TCP Throughput Defaults 

Reverts the TCP Throughput test application to its default factory settings. 

1. The entered value will be rounded to the closest multiple of 1024 Bytes. Unit choices are Bytes, KBytes (default), and 

MBytes.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands