manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 302

Test Setup - Test Configurator, Timer, and System

292

88000 Series

RFC 2544 - Global

Coupled

 is available with 

Bidirectional

 flow direction. When the 

Coupled

 check box is:

Cleared, the decision to increase or decrease the TX Rate of the 
next iteration is taken independently per direction. 

Selected, the decision to increase or decrease the TX Rate of the 
next iteration is taken commonly for both directions. 

Rate Unit

 determines the unit used to display the rate values: 

%

,

 

Mbit/s

, or

 Gbit/s

. 

Pass/Fail Verdict 

check box when selected (default) enables the use 

of the pass/fail verdict. 

Subtests and Estimated Time 

Subtests

 allows enabling the 

Throughput

, 

Back-to-Back

, 

Frame Loss

, 

and 

Latency

 subtests individually. 

Estimated Time (H:MM) 

indicates the estimated time required to 

complete each subtest at best conditions. The total estimated time to 
complete all subtests is also displayed. 

Frame Distribution 

Frame Distribution

 allows selecting either 

RFC 2544

 (default) or 

User 

Defined

 distribution. 

Quantity

 is only available when 

User Defined

 is selected and allows 

selecting the number of frames, from 

1

to

10

 (

7

 by default), in the 

distribution. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands