manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 872

Index

862

88000 Series

Transport Test Applications ................. 119
Wireless Test Applications.................... 144

Modify Structure button ........................... 119
Modify Trib Slots/Channels........................ 282
Modify Trib Slots/Port................................ 343
Modify Wavelength................... 177, 235, 728
module

insertion ................................................ 11
removal ................................................. 11

Modules .................................................... 847
MON ......................................................... 169
Monetary Cost........................................... 262
MPLS ................................................. 256, 498
MPLS Label................................................ 250
MPLS-TP Label Stack.................................. 311
MPLS-TP Mode .......................................... 311
MPLS-TP OAM ........... 140, 306, 453, 489, 514

Traffic .................................................. 606

MPLS-TP OAM Responder.......................... 307
MS............................................................. 457
MS-AIS ...................................................... 457
MSEQ Violation ......................................... 465
Msg Grp/Frame (N_MG) ............................ 231
Msg/Grp (M_MG) ...................................... 231
MSIM ................................................ 437, 439
MSIM Monitoring.............................. 438, 439
MS-RDI ...................................................... 458
MS-REI....................................................... 458
MS-REI Computation Method ................... 346
MTIE.......................................................... 478
MTIE/TDEV................................................. 477
MTU .................................................. 565, 576
Multicast ................................................... 601
Multicast MAC .......................................... 148
Multi-Channel OTN...................................... 51
Multipexer Action...................................... 489
Multiple Connections ................................ 304

N

N1 ............................................................. 676
N2 ............................................................. 678

Name......................................... 198, 319, 522
n-Burst....................................................... 357
NDF ........................................................... 700
Near-End ................................................... 502
Negative .................................................... 237
Negotiation Status............................. 149, 541
Network .................................................... 264
Network block ........................................... 113
Network Details................................. 269, 287
Network Layer ........................................... 249
New Data Flag ........................................... 692
New Pointer............................................... 692
Next HOP Router........................................ 309
n-Frame ..................................................... 357
NI/CSU Emulation ........................................ 67
NJ0 ............................................................ 665
No Defect Time.......................... 160, 186, 281
No NDF...................................................... 700
No Pattern Analysis (Live) .......... 155, 184, 279
No Traffic................................................... 396
No Traffic Time .......................................... 186
Nominal Bit Rate........................................ 344
None ................................................. 335, 337
None (All 1’s)............................................. 643
Non-Unicast............................................... 601
n-Ramp...................................................... 357
Number ..................................................... 346
Number of Burst Sequence........................ 192
Number of Calls................................. 321, 354
Number of Channels.......................... 321, 354
Number of samples ................................... 594
Number of Symbols................................... 481
Number of Trib Slots ................................. 344

O

OA1 ........................................................... 660
OA2 ........................................................... 660
OAM Mode................................ 240, 306, 489
OAM Quick Ping ................................ 253, 310
OAM Type ................................................. 140
OAM Version ............................................. 489

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands