manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 331

Test Setup - Test Configurator, Timer, and System

Power Blazer

321

Services - Profile

Total TX Rate 

Note:

Only available when the 

Service Performance Test

 check box is selected 

(see 

EtherSAM - Global

 on page 193).

Indicates the total transmit rate of all services enabled for transmission. 
Unit selection is available from the 

SLA Parameters

 on page 325. 

Profile 

Profile

 button allows selecting the emulation profile. The selected 

service profile icon, name, and configuration (when applicable) is 
displayed next to the 

Profile

 button. 

Select the emulation profile: 

Voice

, 

Video

, or 

Data 

(default). 

Voice

 

Voice Codec

 choices are 

VoIP G.711

 (default), 

VoIP G.723.1

, and 

VoIP G.729

. 

Number of Calls

 allows the selection of the equivalent number of 

calls that will be generated for the selected stream (default is 

1

). 

CIR 

indicates the committed information rate in Mbps based on 

the number of calls selected. 

Video

 

Video Codec

 choices are 

SDTV (MPEG-2)

 - (default), 

HDTV (MPEG-2)

, and 

HDTV (MPEG-4)

. Only 

SDTV (MPEG-2)

 is 

available with the 10 Mbps interface. 

Number of Channels 

is the equivalent number of channels that 

will be generated for the selected service (default is 

1

). 

CIR

 indicates the committed information rate in Mbps based on 

the number of channels selected. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands