Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 690 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 690

Test Functions

680

88000 Series

Packet Capture

Packet Capture

Capture is used to analyze all or filtered data traffic and save complete or
truncated frames into a buffer. It allows observing network truncated data
precisely, or understanding errors and unwanted behavior.

Note:

Not available with 200/400G and eCPRI dual port topology.

From the

Test

menu, tap

Functions

, and the

Packet Capture

tab.

Note:

For

Dual Port

topology select the port to be displayed.

Capture Source

Specifies what kind of data to be captured.



Interface

captures all received frames and saves them in the capture

buffer.



Filter x

captures only frames that match the selected filter and saves

them in the capture buffer. Select the filter number from the list. Only
enabled filters are available, see

The selected filter will be reserved for data capture and will not be
available for filter configuration.

«
...
688
689
690
691
692
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands