manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 164

Test Setup - Test Configurator, Timer, and System

154

88000 Series

1588 PTP

Pass/Fail Verdict

Pass/Fail Verdict

 check box when selected (default) enables the use of the 

pass/fail verdict. The global pass/fail verdict is based on the following 
criteria: alarms (

Link Down

, 

Loss Sync

, 

Loss Announce

, 

Unusable

 

(G.8265.1), and/or 

QL Mismatch

 (when 

QL Mismatch Monitoring

 is 

enabled)), or the test is automatically aborted (service request denied, 
session canceled, or no reply for G.8265.1; sync message rate changed for 
G.8275.1). 

Restore 1588 PTP Defaults 

Reverts the 1588 PTP test application to its default factory settings. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands