EXFO Power Blazer 88200NGE User Manual Download Page 52

Page: 52 / 887

Graphical User Interface Overview

88000 Series

Application Buttons

MULTI-CH-OTN

Multi-Channel OTN Test Application

NI-CSU

NI/CSU Emulation

OBSAI

OBSAI 3.072 Gbit/s

OBSAI-1.5G

OBSAI 1.536 Gbit/s

OBSAI-6.1G

OBSAI 6.144 Gbit/s

ODU0 OTN

ODU0

ODUflex OTN

ODUflex

ODUflex-HiRate

ODUflex client at 146.7G and above

ODUMUX

ODU Multiplexing Payload Type 20 and 21

OTN-INTR-THRU

OTN Intrusive Through Mode

OTN-MIX-MAPPING Mix-Mapping

capability for Multi-Channel OTN

OTU1 Optical

Transport

Unit-1 (2.7 Gbit/s)

OTU2

Optical Transport Unit-2 (10.7 Gbit/s)

OTU2-1e-2e

Optical Transport Unit-2 Overclocked (11.049/11.096 Gbit/s)

OTU2-1f-2f

Optical Transport Unit-2 Overclocked (11.270/11.317 Gbit/s)

OTU3

Optical Transport Unit-3 (43.018 Gbit/s)

OTU3-e1-e2

Optical Transport Unit-3 Overclocked (44.571/44.583 Gbit/s)

OTU4

Optical Transport Unit-4 (111.81 Gbit/s)

PBBTE

Provider Backbone Bridge Encapsulation (10GE)

PBBTE_40-100GE

Provider Backbone Bridge Encapsulation (40/100GE)

PDH

Plesiochronous Digital Hierarchy

PIM

Passive Intermodulation Analysis

RF-PWR-MASK

Radio Frequency Power Alarming Mask

RFC2544_200-400GE

RFC 2544 test application (200/400GE)

RFC6349

RFC 6349 test application (up to 10GE)

RFC6349_40-100GE

RFC 6349 test application (40/100GE)

RFC6349-EXFOWorx

EXFO|Worx Interop Operation Mode

SDH Synchronous

Digital

Hierarchy

SONET Synchronous

Optical

Network

SONETSDH-INTR-THRU

SONET/SDH Intrusive Through Mode

TCM

Tandem Connection Monitoring STS/AU and VT/TU (SONET/SDH)

Software Option

Description

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands