manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 653

Test Functions

Power Blazer

643

FEAC

Received Messages 

Displays current and previous alarms/status and loopback commands as 
well as the link activity for the received DS3 signal.

Link Activity 

None (All 1’s)

: An all ones pattern (11111111 11111111) has been 

detected in the last second. 

Alarm/Status

: An Alarm/Status codeword has been detected in the 

last second. An Alarm/Status is only detected when receiving at 
least 10 consecutive occurrences of a specific codeword. 

Loopback

: A Loopback command message has been detected in 

the last second. A valid loopback command is detected only when 
receiving 10 consecutive occurrences of a specific 

Loopback 

Command

 immediately followed by 10 occurrences of a specific 

Channel Codeword

. 

Unassigned

: An unassigned message has been detected in the last 

second. An Unassigned message is only detected when receiving 
at least 10 consecutive occurrences of a specific unassigned 
codeword. An 

Alarm/Status

 codeword is also reported since 

Unassigned

 is part of the 

Alarm/Status

 group. 

Alarm/Status and Unassigned

 displays the current and previously 

received 

Codeword

 messages. 

Current

 indicates the last valid message, if any, received in the last 

second of measurment. 

Previous

 indicates the message, if any, that was received just 

before the current measurement. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands