EXFO Power Blazer 88200NGE User Manual Download Page 79

Page: 79 / 887

Test Setup - Test Applications

Power Blazer

EtherSAM (Y.1564)



Typical EtherSAM (Y.1564) test applications:



Supported Interfaces/Rates: 10M to 10G LAN/WAN, 40G and 100G. Dual
Port topology is only available for rates up to 10G WAN.

Network

under test

Testing Unit

Loopback Unit

EXFO Unit

Network

under test

Testing Unit

Remote Unit

EXFO Unit

Network

under test

Testing Unit

EXFO Unit

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands