EXFO Power Blazer 88200NGE User Manual Download Page 422

Page: 422 / 887

Test Results

412

88000 Series

Alarms/Errors Overview



Pre-FEC-SYMB

(Available with 200/400G when

RS-FEC (RX Only)

enabled)

: FEC symbol errors are detected. The

Pre-FEC-SYMB

does not raise

an error, only the count and rate values are reported. Receiving
uncorrectable codeword may affect the Pre-FEC-SYMB error rate.



Pre-FEC-Bit

(Available with 200/400G when

RS-FEC (RX Only)

enabled)

: Indicates the number of bits corrected by the FEC. Receiving

uncorrectable codeword may affect the Pre-FEC-Bit error rate.

FEC (FlexO)

Error



FEC-COR-CW

(FEC Correctable Codeword)

: FEC Codeword that contains errors and were corrected.



FEC-UNCOR-CW

(FEC Uncorrectable Codeword)

: FEC Codeword that contains errors and were not corrected.



Pre-FEC-SYMB

(Pre-FEC Symbol)

: FEC symbol errors are corrected and counted once for each 10-bit

symbol.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands