EXFO Power Blazer 88200NGE User Manual Download Page 427

Page: 427 / 887

Test Results

Power Blazer

417

Alarms/Errors Overview



RPF (Remote PHY Fault)

: The RPF bit is set in the OH.



Excessive Instance Skew

: The current skew is above the configured

Instance Skew Alarm

threshold. The Excessive Instance Skew condition corresponds to a
Loss of lane alignment defect (LOL) as mentioned in the standard.

Errors



MFAS

(Multiframe Alignment Signal)

: Received OH MFAS does not match the expected MFAS value.



OH CRC

: OH received with an invalid CRC.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

EXFO Power Blazer 88200NGE, User Manual, Page: 427 / 887

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews: