manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual, Page: 600 / 887

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 600

Test Results

590

88000 Series

Summary (Traffic Gen & Mon)

Out-of-Sequence

: See 

Streams - Frame Loss / Out-of-Sequence

 on 

page 528. 

Stream

 indicates the stream number and provides stream detailed 

statistics when tapping on its button. 

The following statistics are displayed for the selected stream.

Stream Selection: Select a stream by either using the left/right 
arrow or by tapping over the stream numbers area then tapping on 
a specific stream number. An orange background indicates the 
selected stream. 

Throughput

, 

Jitter

, and 

Latency

 meters display respectively the 

measured Throughput, Jitter, and Latency for the selected stream. 

Note:

The green region defined by the configured threshold corresponds to a 

PASS

 verdict while the red regions corresponds to a

 FAIL

 verdict. The 

Pass/Fail verdict is only displayed when enabled (see 

QoS Metrics

 on 

page 359).

Jitter

: See 

Streams - Jitter

 on page 528. 

Latency

: See 

Streams - Latency

 on page 529.

RX Rate

: See 

Streams - Throughput / Customer Frame Throughput

 

on page 530.

RX Frame Count

 indicates the number of frame received 

matching the selected stream. 

TX Rate

: See 

Streams - Throughput / Customer Frame Throughput

 

on page 530.

TX Frame Count

 indicates the number of transmitted frames 

matching the selected stream. 

Frame Loss

 and 

Out-of-Sequence

: See 

Streams - Frame Loss / 

Out-of-Sequence

 on page 528.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments