EXFO Power Blazer 88200NGE User Manual Download Page 574

Page: 574 / 887

Test Results

564

88000 Series

Summary (iSAM)

For

Dual Test Set

the following values are reported for both local to remote

(

L->R

) and remote to local (

R->L



Service

indicates the service’s number and name.

The pass/fail verdict icon is displayed next to the service name
indicating if the service complies to the configured SLA parameters.



TX CIR

(Mbit/s) indicates the transmitted Committed Information Rate.



FD (ms) (RTT

) (Latency)

indicates the maximum measured

round-trip latency (Frame Delay). The pass/fail verdict is also
displayed.



IFDV (ms) (Jitter)

indicates the maximum measured Inter Frame

Delay Variation. The pass/fail verdict is also displayed.



FLR (%) (Frame Loss)

indicates the maximum percentage of frames

that are lost (Frame Loss Ratio) from the CIR step. The pass/fail verdict
is also displayed.



RX Rate (Mbit/s)

indicates either the measured maximum utilization

throughput for

Service Configuration Test

or the measured average

utilization throughput for

Service Performance Test

. The pass/fail

verdict is also displayed.



Total RX Rate

, available for

Service Performance Test

, indicates the

average utilization throughput for all services (both directions are
displayed for

Dual Test Set

1. RTT is only displayed for Dual Test Set.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands