EXFO Power Blazer 88200NGE User Manual Download Page 300

Page: 300 / 887

Test Setup - Test Configurator, Timer, and System

290

88000 Series

Remote Details (iSAM)

For Manual Loopback Operation Mode



MAC

, available with layer L2, allows entering the destination MAC

address of the remote.



, available with L3/L4, allows entering the destination IP address of

the remote.



Resolved MAC address status,

available with L3/L4, indicates:



Resolving

when the ARP process is resolving.



Resolved

when the ARP process is resolved.



Failed

when the ARP process failed.



Quick Ping

, available with layer L3/L4, tests if the destination IP

address can be reached. A message displays if the ping attempt is

Successful

Failed

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands