EXFO Power Blazer 88200NGE User Manual Download Page 132

Page: 132 / 887

Test Setup - Test Configurator, Timer, and System

122

88000 Series

Modify Structure Button



4 Unframed Physical Lanes

: Independent test pattern in each

physical lane. Available with:

OTU3 (4 Lanes) [43.018 Gbit/s]

OTU3e1 (4 Lanes) [44.571 Gbit/s]

OTU3e2 (4 Lanes) [44.583 Gbit/s]

, and

OTU4 (4 Lanes) [111.81 Gbit/s]



20 Unframed Logical Lanes

: Independent test pattern in each

logical lane. Available with

OTU4 (4 Lanes) [111.81 Gbit/s]

For 88200NGE:

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

EXFO Power Blazer 88200NGE, User Manual, Page: 132 / 887

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews: