Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 793 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 793

Glossary

Power Blazer

783

1588 PTP

The 1588 PTP supports the following Master/Client communication;
however

Unicast

is used for the Telocom Profile.



Multicast

: A Master clock sends its Sync/Follow Up and Delay

Response in a multicast mode. A Client can collect information from
many Master clocks and select the Master clock that is best suited for
its application.



Unicast

: A dedicated communication link is established between the

Master and the Client clock. This mode of operation requires a
negotiation which is initiated by the Client clock.

The 1588 PTP messages can be mapped on the following protocols;
however UDP IPv4 is used for the Telecom Profile.



UDP/IPv4



UDP/IPv6



Ethernet

1588 PTP Profiles

The purpose of a PTP profile is to allow organizations to specify particular
selections of attribute values and optional features of PTP that, when using
the same transport protocol, inter-work and achieve a performance that
meets the requirements of a given application.

«
...
791
792
793
794
795
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands