EXFO Power Blazer 88200NGE User Manual Download Page 663

Page: 663 / 887

Test Functions

Power Blazer

653

OH BERT

OTUx and ODUx

Overhead group check boxes:

Layer Overhead Group

Number of

Bytes

OH Bytes Coordinate

Row

Column

OTU

GCC0

11,12

RES

13,14

ODU

GCC1

1, 2

GCC2

3, 4

APS/PCC

5-8

PM&TCM

TCM ACT

FTFL

Only configurable when the test is not running. Once enabled, the FTFL configuration

and alarm generation and monitoring in the main test are not available for the top ODU

layer.

EXP

13, 14

RES

2
4

1,2
9-14

TCM1

Only configurable when not enabled in the test and when the test is not running.

7, 8, 9

4, 5, 6

1, 2, 3

11, 12, 13

8, 9, 10

5, 6, 7

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands