EXFO Power Blazer 88200NGE User Manual Download Page 562

Page: 562 / 887

Test Results

552

88000 Series

Summary (EtherSAM)



Remote unit in Dual Test Set Mode

indicates that this module is set as

remote but the DTS Connection is not established.



Service Configuration/Performance Test

: Tap

Service Configuration

Test

Service Performance Test

button to view the result summary

of the corresponding test.



Service

indicates the service’s number and name. For

Service

Configuration Test

, the number/name is highlighted in red per

service when VLAN mismatch occurred; in

Dual Test Set

Dual

Port

topology, the direction is also highlighted; in Dual Test Set, the

R -> L

direction label is gray when

VLAN Preservation

is not

supported by the remote module.



Direction

, available with

Dual Test Set

Dual Port

topology,

indicates respectively results for both local (

) and remote (

)

directions, or both port directions.



L2CP

, available when both

L2CP Handling Test

and pass/fail

verdict are enabled, indicates the L2CP handling test pass/fail
verdict.



Service Performance Test

column displays the pass/fail verdict

icon indicating if the service complies to the configured SLA
parameters.



Service Configuration Test

column displays the pass/fail verdict

icon indicating if the service complies to the configured SLA
parameters.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands