EXFO Power Blazer 88200NGE User Manual Download Page 386

Page: 386 / 887

Test Setup - Test Configurator, Timer, and System

376

88000 Series

Traces/PT (FlexO)

Traces/PT (FlexO)

From the

Test

menu, tap

Setup

Test Configurator

, the

FlexO-OTUCn

protocol block, and the

Traces/PT

tab.

OTUCn, ODUCn, and ODUk Buttons

Tap on either the OTU or an ODU button.

SM/PM TTI Traces

Note:

The TTI Traces are configurable for SM (OTUCn) and PM (ODUCn and
ODUk).



Generated Message

Allows editing the SAPI, DAPI, and Operator Specific messages to be
generated.



Expected Message

Allows editing the expected SAPI, and DAPI messages. The expected
message settings are coupled with the

Expected Message

from

Traces/PT (FlexO)

on page 598.

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands