Home
/
EXFO
/
Power Blazer 88200NGE
/
User Manual

EXFO Power Blazer 88200NGE, User Manual

Share

Page: 814 / 887

EXFO Power Blazer 88200NGE User Manual Download Page 814

Glossary

804

88000 Series

G.709 Optical Transport Network (OTN)

Tandem Connection Monitoring (TCM)

TCM enables the user and its signal carriers to monitor the quality of the
traffic that is transported between segments or connections in the network.
SONET/SDH allowed a single level of TCM to be configured, while ITU
G.709 allows six levels of tandem connection monitoring to be configured.
The assignment of monitored connections is currently a manual process
that involves an understanding between the different parties. There are
various types of monitored connection topologies: cascaded, nested and
overlapping. Examples of these topologies are provided in the following
figure.

Tandem Connection Monitoring

«
...
812
813
814
815
816
...
»

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands