manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 312

Test Setup - Test Configurator, Timer, and System

302

88000 Series

RFC 2544 - Subtests

Frame Loss Threshold (%)

 sets the threshold

1

 value of frame loss for 

all frame sizes when applicable. 

Latency Threshold 

/ 

Round-Trip Latency Threshold

 sets the 

threshold value as the maximum delay in 

ms

 or 

μ

s

 for all frame sizes 

when applicable. For 

Dual Test Set

, only available with 

Round-Trip 

Latency Measurement Mode

 (see 

Latency Configuration

 on 

page 299). 

One-Way Latency Threshold

, available for 

Dual Test Set

 with 

One-Way Latency Measurement Mode

 (see 

Latency Configuration

 on 

page 299), sets the maximum one-way latency value in millisecond, 
allowed for all frame sizes. 

Latency Unit

 allows selecting either 

ms

 or 

μ

s

 as the reference unit for 

the 

Latency Threshold

. 

1. The verdict is PASS when the received/measured value is lower or equal to the threshold value. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands