manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 739

Test Control

Power Blazer

729

Lpbk Tool Button (Loopback Tool)

RX Power (dBm)

 indicates the current received power level of the 

optical laser in dBm. 

Green: Power level in range.
Yellow: Power level out-of-range.
Red: Loss of signal or power level is close to damage.
Gray: Invalid operational range value or not supported by the optical 
transceiver. 

Power Range (dBm)

 indicates, when supported, the received power 

level range of the optical laser in dBm. 

RX Frequency (MHz/GHz) 

indicates the frequency of the input signal. 

When no frequency reading is possible, “

--

” is displayed. Not available 

when using an active copper SFP.

LINK 

Auto-Negotiation

 check box when selected, enables the link 

auto-negotiation and allows setting the port 

Speed

, 

Duplex

, 

Flow 

Control

, and 

Local Clock

 parameters. Those settings are not applied 

immediately to the port, they are used only when the negotiation 
process is started and take effect only when the auto-negotiation 
succeeds. However current settings are applied immediately to the 
port when the 

Auto-Negotiation

 check box is cleared. The 

Auto-Negotiation

 check box is automatically selected for 1GE 

Electrical interface and is not configurable. Available with 

10/100/1000M Electrical

 interface. 

Speed

, available with 

10/100/1000M Electrical

 interface, allows the 

selection of the interface rate: 

10M

, 

100M

, 

1GE

, or 

Auto

1

. The 

negotiated speed will be displayed next to the 

Speed

 field selection. 

Duplex

 choices for 

10M 

and

 100M

 electrical interfaces are 

Full Duplex

(default), 

Half Duplex

, and 

Auto

1

. For other rates the 

Duplex is set to 

Full Duplex

. The negotiated duplex will be displayed 

next to the 

Duplex

 field selection. 

1.

Auto

 is only available when the 

Auto-Negotiation

 check box is selected. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands