manualshive.com logo in svg

EXFO Power Blazer 88200NGE, User Manual

Share
Download
EXFO Power Blazer 88200NGE User Manual Download Page 140

Test Setup - Test Configurator, Timer, and System

130

88000 Series

Modify Structure Button

Through Intrusive

 loops the RX signal to the TX port with TX 

overwrite capabilities. Only available with OTN rates. 

Dual RX 

uses two DS1 or DS3 signals at the same time. Both RX 

ports are coupled at the exception of the termination mode. Only 
available with DS1 and DS3 signal rates. 

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands