EXFO Power Blazer 88200NGE User Manual Download Page 501

Page: 501 / 887

Test Results

Power Blazer

491

Link OAM

Remote Error Event Statistics



Date Stamp

indicates the date the last Event Notification OAMPDU

frame was received.



Time Stamp

indicates the time the last Event Notification OAMPDU

event was received by the test equipment.



Window



Threshold



Error Count

Date Stamp

and

Time Stamp

parameters differ from the 802.3 standard definitions.

Symbol Period

Errored symbol Window in second

Frame

Errored frame event Window in second

Frame Period

Errored frame period Window - duration period in number of 64
bytes frames

Frame Seconds

Errored frame seconds summary Window

Symbol Period

Errored symbol threshold in second

Frame

Errored frame event threshold in second

Frame Period

Errored frame period threshold in second

Frame Seconds

Errored frame seconds summary threshold in second

Symbol Period

The number of symbol errors in Window

Frame

The number of frame event errors in Window

Frame Period

The number of frame period errors in Window

Frame Seconds

The number of frame seconds summary errors in Window

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands