EXFO Power Blazer 88200NGE User Manual Download Page 57

Page: 57 / 887

Power Blazer

Test Setup - Test Applications

The Power Blazer offers the following test applications.

Type

Application

Available on

Page

8870/8880 88200NGE 88260 88400NGE/88460

Intelligent Apps

Transport

X 52

SONET/SDH - DSn/PDH BERT

Ethernet

X -

X 73

X X

Carrier Ethernet OAM

Cable Test

- -

Sync

1588 PTP

X -

SyncE

Wander

8880

Fibre Channel

FC BERT

Summary of Contents for Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands

EXFO Power Blazer 88200NGE, User Manual

Search results

Summary of Contents for Power Blazer 88200NGE

Reviews:

Brands by name

Popular brands