Hitachi SJ Series, User Manual

Page: 58 / 786

7.3 Use the Backing Plate
・
P1
P1
P1
P1
・
P1
P1
1. When a conduit tube is not connected
2. When a conduit tube is connected
Chapter 7
7.3 Use the Backing Plate
・
When connecting wires to apply high voltage on the
AL terminal, draw out the plate separately from the
wiring of control circuit.
Backing plate (i)
P1-00330-LFF
～
P1-00175-HFF
～
Backing pla
P1-00800-LFF
～
P1-00400-HFF
～
・
Cut the connections between the unnecessary part
and backing plate using nippers, radio pliers, or
cutter, to cut off the unnecessary part for wiring.
Backing plate (iii)
P1-01250-L (P1-
P1-00770-H (P1
1. When a conduit tube is not connected
Cut the rubber bushing to create a notch using
nippers or a cutter for wiring.
2. When a conduit tube is connected
Remove the rubber bushing in the portion where
a conduit tube is to be connected, a
connect the conduit tube.
Do not remove rubber busings from
the wiring section unless a conduit
tube is connected.
cause the edge of backing plate to
damage the cable sheath, leading to
short circuit
!
▼
▼
Electric
shock
Ground
fault
Chapter 7
7.3 Use the Backing Plate
connecting wires to apply high voltage on the
AL terminal, draw out the plate separately from the
wiring of control circuit.
Backing plate (i)
～
P1-00600-LFF
～
P1-00310-HFF
Backing plate (ii)
～
P1-01240-LFF
～
P1-00620-HFF
Cut the connections between the unnecessary part
and backing plate using nippers, radio pliers, or
cutter, to cut off the unnecessary part for wiring.
Backing plate (iii)
-300L)
～
P1-01540
(P1-300H)
～
P1-03610
1. When a conduit tube is not connected
Cut the rubber bushing to create a notch using
nippers or a cutter for wiring.
2. When a conduit tube is connected
Remove the rubber bushing in the portion where
a conduit tube is to be connected, a
connect the conduit tube.
Do not remove rubber busings from
the wiring section unless a conduit
tube is connected.
cause the edge of backing plate to
damage the cable sheath, leading to
short circuit or ground fault.
7.3 Use the Backing Plate
connecting wires to apply high voltage on the
AL terminal, draw out the plate separately from the
wiring of control circuit.
LFF (P1-055LFF
～
HFF (P1-055HFF
～
LFF (P1-150LFF
～
HFF (P1-150HFF
～
Cut the connections between the unnecessary part
and backing plate using nippers, radio pliers, or
cutter, to cut off the unnecessary part for wiring.
01540-L (P1-550L)/
03610-H (P1-1320H)
1. When a conduit tube is not connected
Cut the rubber bushing to create a notch using
nippers or a cutter for wiring.
2. When a conduit tube is connected
Remove the rubber bushing in the portion where
a conduit tube is to be connected, a
connect the conduit tube.
Do not remove rubber busings from
the wiring section unless a conduit
tube is connected. Doing so may
cause the edge of backing plate to
damage the cable sheath, leading to
or ground fault.
connecting wires to apply high voltage on the
AL terminal, draw out the plate separately from the
P1-110LFF)
～
P1-110HFF)
P1-220LFF)
～
P1-220HFF)
Cut the connections between the unnecessary part
and backing plate using nippers, radio pliers, or
cutter, to cut off the unnecessary part for wiring.
550L)/
1320H)
1. When a conduit tube is not connected
Cut the rubber bushing to create a notch using
2. When a conduit tube is connected
Remove the rubber bushing in the portion where
a conduit tube is to be connected, and then
Do not remove rubber busings from
the wiring section unless a conduit
Doing so may
cause the edge of backing plate to
damage the cable sheath, leading to
or ground fault.
7-3
Wire Connection and Optional Devices
connecting wires to apply high voltage on the
AL terminal, draw out the plate separately from the
Cut the connections between the unnecessary part
and backing plate using nippers, radio pliers, or
cutter, to cut off the unnecessary part for wiring.
Cut the rubber bushing to create a notch using
Remove the rubber bushing in the portion where
・
Backing plate (i)
・
Backing plate (ii)
・
Backing plate (iii)
Wiring of
control circuit
Wiring of main
circuit
Wire Connection and Optional Devices
Backing plate (i)
Backing plate (ii)
Backing plate (iii)
Wiring of
control circuit
Wiring of main
circuit
Wiring of
control circuit
Wiring of main
circuit
Backing plate
Please contact the sales officer of our
company for the latest information.
Wire Connection and Optional Devices
Backing plate (i)
Backing plate (ii)
Backing plate (iii)
Unnecessary part
Please contact the sales officer of our
company for the latest information.
Wire Connection and Optional Devices
Unnecessary part
Rubber bushing
Please contact the sales officer of our
company for the latest information.
Wire Connection and Optional Devices
Unnecessary part
Connection
Rubber bushing
Please contact the sales officer of our
company for the latest information.
Wire Connection and Optional Devices
Connection