Hitachi SJ Series, User Manual

Page: 139 / 786

Chapter 10
10.4 Let’s Configure Settings for Test
10.4.1
•
•
•
Display description
①
②
Chapter 10
10.4 Let’s Configure Settings for Test
Runs!
10.4.1 To perform test runs via operator
keypad VOP
• Want to perform a test run using operator keypad
VOP.
• From the initial screen displayed at power
move to “H03” with the LEFT/RIGHT (
• For procedure of
Let’s Set Parameters”.
Display description
①
②
Q
▼
Chapter 10
10.4 Let’s Configure Settings for Test
Runs!
o perform test runs via operator
keypad VOP
Want to perform a test run using operator keypad
From the initial screen displayed at power
move to “H03” with the LEFT/RIGHT (
For procedure of changing parameters, see "9.3
Let’s Set Parameters”.
Display description
Menu
oFW
STOP
Output Frequency
FA-01
Menu
oFW
STOP
Output Frequency
AA101
07: Parameter set
10.4 Let’s Configure Settings for Test
o perform test runs via operator
Want to perform a test run using operator keypad
From the initial screen displayed at power
move to “H03” with the LEFT/RIGHT (
changing parameters, see "9.3
60.00Hz
oFW
M1
Output Frequency
0.00Hz
oFW
M1
Output Frequency
07: Parameter set-up
10.4 Let’s Configure Settings for Test
o perform test runs via operator
Want to perform a test run using operator keypad
From the initial screen displayed at power-on,
move to “H03” with the LEFT/RIGHT (
) keys.
changing parameters, see "9.3
Option
M1
H03
0.00 Hz
60.00 Hz
Option
M1
H03
0.00 Hz
10-4
10.4 Let’s Configure Settings for Test
Want to perform a test run using operator keypad
) keys.
changing parameters, see "9.3
• To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
or check the following parameters.
①
②
③
④
Setting item
①
Frequency command destination selection [AA101]
Set the frequency command destination to “07:
Parameter set
②
Main speed command [FA
When the frequency command destination is set to
“07: Parameter set
(Operator keypad)” will be shown.
If a frequency command is set in this state, the value
will be shown at the bottom
A
To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
or check the following parameters.
Frequency command destination selection
[AA101]
Main speed command
Operation command destination selection
Setting the electronic thermal level of motor
[bC110]
Setting item
Frequency command destination selection [AA101]
Set the frequency command destination to “07:
Parameter set-up”.
Main speed command [FA
When the frequency command destination is set to
“07: Parameter set
(Operator keypad)” will be shown.
If a frequency command is set in this state, the value
will be shown at the bottom
A
To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
or check the following parameters.
Frequency command destination selection
Main speed command [FA
Operation command destination selection
Setting the electronic thermal level of motor
Frequency command destination selection [AA101]
Set the frequency command destination to “07:
up”.
Main speed command [FA-01]
When the frequency command destination is set to
-up”, “Main speed command
(Operator keypad)” will be shown.
If a frequency command is set in this state, the value
will be shown at the bottom command monitor area.
To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
or check the following parameters.
Frequency command destination selection
[FA-01]
Operation command destination selection
Setting the electronic thermal level of motor
Frequency command destination selection [AA101]
Set the frequency command destination to “07:
When the frequency command destination is set to
up”, “Main speed command
(Operator keypad)” will be shown.
If a frequency command is set in this state, the value
command monitor area.
Test Run
To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
Frequency command destination selection
Operation command destination selection [AA111]
Setting the electronic thermal level of motor
Frequency command destination selection [AA101]
Set the frequency command destination to “07:
When the frequency command destination is set to
up”, “Main speed command
If a frequency command is set in this state, the value
command monitor area.
Run
To perform a test run only via operator keypad VOP,
set the following parameters from the initial value,
[AA111]