Hitachi SJ Series, User Manual

Page: 41 / 786

6.2 Installation Environment
*
Chapter 6
6.2 Installation Environment
The inverter uses plastic parts. When carrying
the inverter, handl
damage to the parts.
Do not carry the inverter by holding the front or
terminal block cover.
Doing so may cause the
Avoid installing the inverter in a place where
the ambient
the allowable range, as defined by the
standard inverter specification.
* Temperature requirements vary
See “Chapter 20 Specifications”.
Carrier derating may be required.
Avoid installing the inverter in a place where
the relative humidity goes above or below the
allowable range (20% to 90% RH), as defined
by the standard inverter specification. Avoid a
place where the inverter is
condensation.
◆
Transportation
◆
Ambient temperature
◆
Humidity
Chapter 6
6.2 Installation Environment
The inverter uses plastic parts. When carrying
the inverter, handl
damage to the parts.
Do not carry the inverter by holding the front or
terminal block cover.
Doing so may cause the
Avoid installing the inverter in a place where
the ambient temperature goes above or below
the allowable range, as defined by the
standard inverter specification.
Temperature requirements vary
See “Chapter 20 Specifications”.
Carrier derating may be required.
Avoid installing the inverter in a place where
the relative humidity goes above or below the
allowable range (20% to 90% RH), as defined
by the standard inverter specification. Avoid a
place where the inverter is
condensation.
Transportation
Ambient temperature
Humidity
6.2 Installation Environment
The inverter uses plastic parts. When carrying
the inverter, handle it carefully to prevent
damage to the parts.
Do not carry the inverter by holding the front or
terminal block cover.
Doing so may cause the inverter to fall.
Avoid installing the inverter in a place where
temperature goes above or below
the allowable range, as defined by the
standard inverter specification.
Temperature requirements vary depending on the selected load rating.
See “Chapter 20 Specifications”.
Carrier derating may be required.
Avoid installing the inverter in a place where
the relative humidity goes above or below the
allowable range (20% to 90% RH), as defined
by the standard inverter specification. Avoid a
place where the inverter is subject to
Ambient temperature
Temperature
requirements
20 to 90%RH
The inverter uses plastic parts. When carrying
e it carefully to prevent
Do not carry the inverter by holding the front or
inverter to fall.
Avoid installing the inverter in a place where
temperature goes above or below
the allowable range, as defined by the
standard inverter specification.
depending on the selected load rating.
Avoid installing the inverter in a place where
the relative humidity goes above or below the
allowable range (20% to 90% RH), as defined
by the standard inverter specification. Avoid a
subject to
Temperature
requirements
6-2
The inverter uses plastic parts. When carrying
Do not carry the inverter by holding the front or
Avoid installing the inverter in a place where
temperature goes above or below
depending on the selected load rating.
Avoid installing the inverter in a place where
the relative humidity goes above or below the
allowable range (20% to 90% RH), as defined
by the standard inverter specification. Avoid a
Do not install and operate the inverter if it is
damaged or parts are missing.
Fall
Leave sufficient space around the inverter.
Measure the temperature in a position about 5
cm from the bottom
and check that the measured temperature is
within the allowable range. Operating the
inverter at a temperature outside this range will
shorten the inverter life (especially the
capacitor life).
depending on the selected load rating.
Condensation inside the inverter will result in
short circuits and malfunctioning of electronic
parts. Also avoid places where the inverter is
exposed to direct sunlight.
Water
drops
Do not install and operate the inverter if it is
damaged or parts are missing.
Leave sufficient space around the inverter.
Measure the temperature in a position about 5
cm from the bottom
and check that the measured temperature is
within the allowable range. Operating the
inverter at a temperature outside this range will
shorten the inverter life (especially the
capacitor life).
Condensation inside the inverter will result in
short circuits and malfunctioning of electronic
parts. Also avoid places where the inverter is
exposed to direct sunlight.
Installation
Do not install and operate the inverter if it is
damaged or parts are missing.
Leave sufficient space around the inverter.
Measure the temperature in a position about 5
cm from the bottom-center point of the inverter,
and check that the measured temperature is
within the allowable range. Operating the
inverter at a temperature outside this range will
shorten the inverter life (especially the
Condensation inside the inverter will result in
short circuits and malfunctioning of electronic
parts. Also avoid places where the inverter is
exposed to direct sunlight.
Direct
sunlight
Installation
Do not install and operate the inverter if it is
Leave sufficient space around the inverter.
Measure the temperature in a position about 5
point of the inverter,
and check that the measured temperature is
within the allowable range. Operating the
inverter at a temperature outside this range will
shorten the inverter life (especially the
Condensation inside the inverter will result in
short circuits and malfunctioning of electronic
parts. Also avoid places where the inverter is
Installation
Measure the temperature in a position about 5
point of the inverter,
inverter at a temperature outside this range will
Condensation inside the inverter will result in
short circuits and malfunctioning of electronic
parts. Also avoid places where the inverter is