BMW K 1200RS Repair Manual Download

Page: 159 / 416

13.9

13 54

Removing/installing throttle-

valve rail

–

Take off the right side section of the fairing
(

46.10).

•

Disconnect the hose clip (arrow) for the crank-
case breather from the right, under the frame.

•

Pull off the hose.

–

Remove intake air silencer.

•

[Cruise control]

Disconnect plug (4) for switch

of cruise-control system.

•

Disconnect the earth (ground) cable (3) from the
throttle-valve rail.

•

Disconnect plug of throttle-valve
potentiometer (2).

•

Disconnect plug of throttle-valve actuator (1).

•

[Activated charcoal filter]

Disconnect breather

hose to timing valve from y-piece.

•

Disconnect the plug (arrow) for the fan.

Note:

It is not necessary to open the cable ties when re-
moving the fuel injection rail.

•

Remove the fuel injection rail and secure it to the
frame together with the wiring harness (

13.7).

•

Slacken screws securing hose clips at intake
stubs.

•

Remove throttle-valve rail from intake stubs.

Important:

[Cruise control]

Do not remove retaining plate (6):

the screws locate the throttle-valve stubs.

•

[Cruise control]

Disengage throttle-opener

cable (7) from its pull at the throttle-valve rail.

KR130260

K41130020

KR170140

KL130050

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands