manualshive.com logo in svg

BMW K 1200RS, Repair Manual

Share
Download
BMW K 1200RS Repair Manual Download Page 39

00.30

00 00 

Handover

This is the ideal opportunity to familiarise the cus-
tomer with the motorcycle in order to ensure the 
customer’s satisfaction and safety.

•

The user must be given the following information:

–

The centre and side stands do not retract auto-
matically, which makes it easier to raise the mo-
torcycle or place it on its side stand.

–

The engine will run even when the side stand is 
extended.

–

Before checking the engine oil level, the engine 
must be switched off for at least 10 minutes and 
the motorcycle must be standing on its main 
stand on a flat, level surface.

•

Demonstrate or explain the following points to 
the customer:

–

How to adjust the seat, the windscreen, the left 
and right handlebars, the footrests and the gear-
shift lever

–

How to remove and install the seat

–

Documentation and stowage space

–

Toolkit and stowage space

–

Oil funnel

d

 Warning:

The motorcycle may be operated only with the cap 
for the battery's positive terminal closed and the tool 
tray in position.

[Integral ABS]

 When installing the battery, make 

sure that the position of the protector for the brake 
hose is correct.

–

How to remove and install the battery

–

How to adjust the mirrors

–

Controls

–

Instruments and telltale and warning lights

–

Procedure and noises of BMW Integral ABS self-
diagnosis

L

 Note:

Starting on gradients:
Always switch on the ignition with gear engaged and 
both brake levers released. Self-diagnosis cannot 
be performed successfully if you do not follow this 
procedure. When self-diagnosis completes, apply 
the brakes, disengage the clutch, and start the 
engine.

–

Sequence of the BMW Integral ABS pull-away 
test

–

BMW Integral ABS residual braking function, for 
example when ignition is switched off

–

How to adjust the rear suspension strut

–

Optional equipment and accessories fitted

–

Running-in recommendations and inspection 
intervals

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands