manualshive.com logo in svg

BMW K 1200RS, Repair Manual

Share
Download
BMW K 1200RS Repair Manual Download Page 70

00.61

21 00 

Checking clutch fluid level, cor-

recting if necessary

(Inspections II and III)

e

 Attention:

Do not allow brake fluid to come into contact with 
painted parts of the motorcycle, because brake fluid 
destroys paint.

–

Place the motorcycle on its centre stand so that 
it is level.

•

Turn the handlebars to the right.

L

 Note:

The level of fluid in the expansion tank increases as 
wear to the clutch lining increases.

e

 Attention:

Reliable operation of the clutch is not ensured when 
the level of the fluid (arrow) is below the upper mar-
king ring.

•

The clutch fluid should never drop below the le-
vel for initial filling: if it does, check the clutch sy-
stem for leaks.

Specified level with a new clutch liner:

No more than

................................................. upper ring marking

Brake fluid

....................................................DOT 4

K41000010

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands