BMW K 1200RS Repair Manual Download Page 121

Page: 121 / 416

11.35

Assembling tensioning gear

•

Insert the tensioning spring.

•

Attach the tensioning spring to the pin in the ten-
sioning gear and turn it clockwise with the coun-
ter-holder,

BMW No. 12 4 600

until the pin of the

tensioning gear engages the hole in the gear.

•

Clamp the tensioning gear with damper housing
together in a vice with soft jaws.

•

Measure distance “

” from the base of the ball

bearing seat to the tensioning gear.

Important:

The thickness of the spacing washer must never ex-
ceed this measurement.

•

Place a suitable spacing washer (arrow) on the
tensioning gear.

Note:

Use temperature measuring device,

BMW No. 00 1 900

, to check heat rise.

•

Heat the ball bearing to approx. 80°C (176°F) and
place it in position (with shoulder uppermost).

•

Clamp the damper housing and the ball bearing
together in the vice (with soft jaws).

•

Insert retaining ring (4) with suitable pliers in the
groove in front of the bearing.

•

The retaining ring must snap completely into the
groove.

KR110470

KR110480

KR110460

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands