BMW K 1200RS Page 37 Repair Manual Download

Page: 37 / 416

00.28

00 00

Adjusting footrests left/right

Warning:

If the motorcycle is to be ridden by a sporty rider, fit
the footrests in the upper position.

•

Remove the left/right footrest support.

•

Install the left/right footrest support in the alter-
native position.

Note:

Make sure that the left and right footrest supports
are both in either the upper or the lower position.

00 00

Adjusting gearshift lever

•

Remove screw (arrow) and reposition the gear
shift lever to suit the altered footrest position.

Tightening torque:

Footrest system to frame.............................. 21 Nm
Gearshift lever ................................................ 8 Nm

KR460190

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands