BMW K 1200RS Repair Manual Download | Manualshive

Page: 311 / 416

background image

34.17

3400

[Integral ABS] Filling brake

system

d

Warning:

Comply with all maintenance and repair instructions
and always work through the various steps in the
correct order.
Use only new brake fluid from freshly opened con-
tainers.

3400

[Integral ABS] Filling the wheel

circuit

e

Attention:

Do not allow brake fluid to come into contact with
painted parts of the motorcycle, because brake fluid
destroys paint.

L

Note:

Only check the brake system after bleeding of all
brake circuits.
The wheel circuit is filled via the brake caliper to en-
sure that the system is free of air bubbles.

d

Warning:

On filling, make sure no air bubbles enter the brake
caliper via the injector and the silicon hose.

–

The brake caliper is fitted.

Filling the front wheel circuit

•

Open the cap (2).

•

Fill injector,

BMW No. 34 2 551

, and silicon hose

with 80 ml (0.1407 Imp. pint/0.0845 US quart) of
brake fluid.

L

Note:

Press the plunger of the injector until the silicon
hose is free of bubbles.

•

Connect bubble-free injector,

BMW No. 34 2 551

, to bleed screw of left brake

caliper.

•

Open the bleed screw (6).

•

Inject brake fluid into the left-hand brake caliper.

•

Close the bleed screw (6) of the brake caliper.

•

Remove injector,

BMW No. 34 2 551

.

KR340570

1

3

4

2

MAX

MIN

MIN

MIN

MAX

5

KR340700

34 2 551

6

«
...
309
310
311
312
313
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Baotian Pages: 30

Brand: MadStad Engineering Pages: 2

Brand: Memphis Shades Pages: 2

H-X-ADV-07-01-AL

Brand: SRC Pages: 6

Rally Pack Value Series

Brand: Dowco Pages: 3

Brand: Free Spirits Pages: 28

Brand: Honda Pages: 127

XRM125 CFT125 2020

Brand: Honda Pages: 111

Brand: Yamaha Pages: 338

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 100

Road Star XV17AWX

Brand: Yamaha Pages: 110

Brand: Yamaha Pages: 650

Brand: Honda Pages: 4

Brand: hepco & becker Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands