BMW K 1200RS Repair Manual Download

Page: 224 / 416

23.16

23 12

Disassembling/assembling out-

put shaft

23 12 Disassembling output shaft

Important:

To avoid damaging the needle roller bearings on the
splines, spread the rollers carefully at the end faces.

•

Using universal puller,

BMW No. 00 7 500

remove grooved ball bearing (18) together with
1st gear shift wheel (20).

•

Remove spacing washer (19), 1st gear shift
wheel (20), needle roller bearing (21) and spacing
washer (22).

•

Remove the sliding gearwheel for 5th gear (7).

•

Remove circlip (8), backup washer (9), shift
gearwheel for 3rd gear (10) and needle roller
bearing (11).

•

Remove backup washer (12), 4th gear shift
wheel (13), needle roller bearing (14) and backup
washer (15).

•

Remove circlip (16) and sliding gearwheel for
6th gear (17).

•

Turn output shaft (6) other way round and clamp
into the vise with soft jaws.

•

Use universal puller,

BMW No. 00 7 500

, to pull

off grooved ball bearing (1).

•

Remove shim washer (2), needle roller
bearing (3), shift gearwheel for 2nd gear (4) and
thrust washer (5).

KR230100

00 7 500

KR230110

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands