BMW K 1200RS Page 53 Repair Manual Download | Manualshive

Page: 53 / 416

background image

00.44

34 00

[Integral ABS] Checking opera-

tion of brake system and freedom
from leaks; repairing if necessary.

(Inspection III)

•

Check all brake lines for damage and correct po-
sitioning.

•

Wipe down all threaded unions on the brake lines
and check them.

•

Switch on the ignition.

L

Note:

After switching on the ignition, always wait for the
BMW Integral ABS to complete its self-diagnosis.
Do not operate the brake lever until self-diagnosis
has completed.

d

Warning:

When performing maintenance and repair work on
the BMW Integral ABS, avoid rapid and forceful
pumping of the brakes.

•

Apply the brake hard and hold on in this position
for a short time.

•

After this, inspect the brake lines for leaks.

d

Warning:

If defective, all lines and threaded unions in the bra-
ke system must be replaced without delay.

«
...
51
52
53
54
55
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: hepco & becker Pages: 4

Stelvio 1200 MY11 2011

Brand: MOTO GUZZI Pages: 385

Grizzly Minicross RCX/12 50CC

Brand: Malaguti Pages: 33

Brand: Kenwood Pages: 36

Brand: Kenwood Pages: 97

Brand: Arai Helmet Pages: 28

Brand: Arai Helmet Pages: 52

Brand: Arai Helmet Pages: 60

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 44

Brand: Yamaha Pages: 92

WARRIOR XV17PCT

Brand: Yamaha Pages: 97

WARRIOR XV17PCC

Brand: Yamaha Pages: 97

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 96

Brand: Yamaha Pages: 95

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands