BMW K 1200RS Repair Manual Download | Manualshive

Page: 370 / 416

background image

46.36

46 51

Measuring wheel track offset

•

Place the motorcycle on its main (centre) stand
on a flat, level surface.

•

Measure wheel rim width at front and rear and
make a note of the figures.

•

Place track alignment gauge,

BMW No. 36 3 920

, against the left or right side

of the motorcycle.

L

Note:

In order to use the track alignment gauge on either
the left or right side, simply screw the supports in on
the other side.

•

Adjust supports (1) so that the measuring plane
is as close as possible to the wheel centreline.
The gauge must slide freely up to the motorcy-
cle.

•

Adjust measuring stops (arrows) until they con-
tact the rim - not the tyre.

•

Connect hook (2) to a wheel spoke and use it to
pull the gauge firmly up to the wheel.

•

Align front wheel parallel with the gauge.

•

Release tension in the track alignment gauge by
raising it by approx. 5 mm (0.1969 in) at the front
and lowering it again.

•

Using a depth gauge (3) or ruler, measure the
distance from the outer edge of the gauge to the
front wheel rim at the front and rear of the wheel
and make a note of the figures. Deduct the width
of the track alignment gauge.

L

Note:

The average of these two values less the width of
the track alignment gauge is measured value “B”.

KR460370

2

36 3 920

1

3

«
...
368
369
370
371
372
...
»

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Brand: Tao Motor Pages: 3

Brand: P.Lindberg Pages: 26

Brand: MOTO GUZZI Pages: 266

Super Tenere XTZ1200Z

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 351

Brand: Yamaha Pages: 96

Brand: Leatt Pages: 23

Brand: hepco & becker Pages: 6

Brand: Yamaha Pages: 81

2011 Star XV250A

Brand: Yamaha Pages: 90

2011 V Star XVS650A

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 102

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 96

2010 V Star XVS650AZ

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands