BMW K 1200RS Page 149 Repair Manual Download

Page: 149 / 416

12.14

12 41

Disassembling and reassembling

starter motor

•

Clamp the starter motor in the vise (with soft
jaws) at its retaining lugs.

•

Unscrew tie-rods (14).

•

Pull off bearing cap (13).

•

Remove seal (11) and O-ring (12) and inspect
them for damage.

•

Pull out armature (1).

•

Take off spacing washer (2).

•

Installation is the reverse of the removal proce-
dure.

Removing/installing brush holder

•

Unscrew hex nut (6).

•

Take off outer insulating washer (5).

•

Take off brush holder plate (3) with carbon brush
holder (9), inner insulator (8) and O-ring (7).

•

Installation is the reverse of the removal proce-
dure.

Replacing carbon brushes

•

Using a small screwdriver, raise spring (10) and
pull the carbon brush out in the direction of the
arrow.

Note:

Insert the carbon brush with the angled side toward
the spring.

KR120090

12 11

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands