BMW K 1200RS Repair Manual Download Page 69

Page: 69 / 416

00.60

34 00

Rear brake

Force back the brake pistons.

Attention:

Do not scrape the wheel – mask it off if necessary.

–

Remove rear brake pads (

00.43).

•

Using resetting tool,

BMW No. 34 1 531

, force

the pistons fully back.

Change and bleed the rear brake circuit.

–

Place motorcycle on its centre stand.

Attention:

Do not allow brake fluid to come into contact with
painted parts of the motorcycle, because brake fluid
destroys paint.

•

Take off the reservoir cover.

•

Add brake fluid up to the

MAX

mark (arrow).

•

Connect the brake bleeding device to the bleed
screw on the brake caliper.

•

Open the bleed screw by half a turn.

Attention:

Brake fluid level must not drop below the

MIN

mark

during the bleeding process, otherwise air will be
drawn into the brake system.Bleed the system again
if this happens.

•

Draw off brake fluid until it emerges clear and
free from air bubbles.

•

Close the bleed screw.

•

Bleed the system again if necessary.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

•

Top up the brake fluid in the reservoir to the spe-
cified level (

00.57)

•

Fit brake pads.

•

Bed in the brake pads.

•

Check the operation of the brake system.

Attention:

Dispose of old brake fluid in an environmentally-fri-
endly manner.

Brake fluid

...................................................DOT 4

Tightening torque:

Bleed screw ................................................. 10 Nm

KR340820

34 1 531

KR340290

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands