BMW K 1200RS Repair Manual Download Page 110

Page: 110 / 416

11.24

Assembling pistons

•

Install piston rings, using piston-ring pliers.

Note:

The “Top” inscription is uppermost or according to
the installed position previously noted.

1st groove: rectangular-section ring.
2nd groove: micro-chamfer ring; note pin for ring gap.
3rd groove: U-Flex ring with spring.

Note:

The gap in the spring must be offset 180° in relation
to the Flex ring gap.

Checking cylinder dimensions

•

Set the internal micrometer to the nominal cylin-
der bore diameter.

•

Measure the cylinder bore at three heights and in
a crosswise pattern: in the direction of forward
travel and at a right angle to it.

Checking that conrod bores are parallel

•

The difference over the reference length “

”

must not exceed 0.06 mm (0.0024 in).

Reference length “

” ................ 150 mm (5.9055 in)

KR110371

KR110380

150

0,06

KR110400

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Brands by name

Popular brands