BMW K 1200RS Repair Manual Download

Page: 329 / 416

36.6

36 31

Removing/installing wheel

bearings

–

Place the front wheel on two wooden blocks,
making sure the brake disc is clear.

36 31

Removing left/right wheel bear-

ings

Note:

There is no circlip at the right wheel bearing.

•

Lever out shaft seal (1).

•

Remove circlip (2) with suitable pliers.

•

Place support ring,

BMW No. 36 6 640

, on

wheel hub.

•

Heat bearing seat to 60 °C (140 °F).

•

Pull out wheel bearing (3) with puller,

BMW No. 00 8 570

, and internal puller 21/4,

BMW No. 00 8 573

•

Remove spacer sleeve (4).

KR360020

KR360060

00 8 570

00 8 573

36 6 640

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands