BMW K 1200RS Page 186 Repair Manual Download

Page: 186 / 416

17.9

17 11

Removing/installing fan

17 11

Removing/installing left fan

–

Take off the left side section of the fairing
(

46.10)

•

Remove the fasteners (arrows). Take off the radi-
ator air inlet guide.

Note:

Illustrations for the following work:

Remove left radiator.

•

Remove retaining clips with washers for radiator.

•

Loosen air outlet guide mountings. Take off air
outlet guide.

•

Disconnect fan plug.

•

Release the fasteners (arrows) for the fan at the
radiator.

•

Take off the fan.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Fan to radiator
(clean apply Loctite 243) .................. 2 Nm

17 11

Removing the right fan

–

Remove the right side section of the fairing
(

46.10).

•

Remove the fasteners (arrows).

Note:

Illustrations for the following work:

Remove left radiator.

•

Remove retaining clips with washers for radiator.

•

Loosen air outlet guide mountings. Take off air
outlet guide.

•

Disconnect fan plug.

•

Release fasteners for fan.

•

Take off the fan.

•

Installation is the reverse of the removal proce-
dure.

Tightening torque:

Fan to radiator
(clean apply Loctite 243) .................. 2 Nm

KR170030

KR170070

KR170050

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands