BMW K 1200RS Repair Manual Download

Page: 115 / 416

11.29

1100

Disassembling/assembling inter-

mediate flange

Removing the driver bearing

•

Remove thrust plate (1).

•

Take off cup spring (2).

•

Remove ball bearing (3) with puller,

BMW No. 00 8 570

, and internal puller 21/3,

BMW No. 00 8 574

•

Remove snap ring (4).

Installing driver bearing

•

Install the snap ring (4).

Note:

Use temperature measuring device,

BMW No. 00 1 900,

to check heat rise.

•

Heat the intermediate flange at the bearing seat
to approx. 120 °C (248 °F).

•

Press the ball bearing on as far as the snap ring.

•

Insert the cup spring with the larger diameter fac-
ing the bearing.

•

Install the thrust plate with the large cutout at the
top.

Tightening torque:

Thrust plate to intermediate flange
(clean apply Loctite 243) .................. 9 Nm

KR110120

KR110130

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands