BMW K 1200RS Repair Manual Download

Page: 33 / 416

00.24

00 00

Filling and charging the battery

Remove the battery

Warning:

Battery acid is highly caustic.
Protect your eyes, face, hands, clothing and the
paintwork.

•

Remove the seat.

•

Take out the tool wallet.

•

Remove the tool tray.

Attention:

Disconnect the battery only when the ignition is
switched off.
Disconnect the negative battery terminal first, then
the positive terminal.

•

Disconnect both ground leads (5) from the bat-
tery and insulate.

•

Disconnect the positive lead (4) from the battery.

•

Release the fasteners (2) at the battery retaining
plate (1). Take off the battery retaining plate (1).

•

Pull off the battery breather hose (3).

•

Remove battery from holder.

•

Set the battery down on a level surface.

Filling and charging the battery

•

Pull off the battery breather hose (3).

Battery sulphuric acid ......................... Density 1.28

•

Top up the battery acid to the MAX mark.

•

Allow the battery to stand for at least an hour.

•

Shake the battery slightly to allow the remaining
air bubbles to escape.

•

If necessary, top up again to the MAX mark with
battery acid.

•

Charge the battery and allow to stand for 24
hours.

Charge current (A)

......................... 10 % of rated battery capacity (Ah)

•

If necessary, top up the acid level to the MAX
mark with distilled water.

•

Make a note of the charging date on the battery.

•

Clean the battery terminals and grease them with
acid-proof grease.

Acid-proof battery terminal grease

................................................e.g. Bosch Ft 40 V1

Installing the battery

Warning:

[Integral ABS]

Make sure that the brake hose pro-

tector (7) is correctly seated.
Make sure that brake fluid hoses (6, 8) are correctly
routed to avoid rubbing.

K41UB0030

K41UB0080

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands