manualshive.com logo in svg

BMW K 1200RS, Repair Manual

The BMW K 1200RS Repair Manual is the comprehensive guide for motorcycle enthusiasts seeking to maintain and fix their BMW K 1200RS model. This essential manual provides step-by-step instructions and detailed diagrams to aid in repairs and maintenance tasks. Download your free copy from our website, manualshive.com.

Share
Download
background image

00.31

Contents

Page

00

Maintenance 

..................................................................................................................................35

Key to maintenance intervals 

..............................................................................................35

General instructions 

.................................................................................................................35

Pushing the motorcycle onto a workshop platform (

a 

00.21) ............................................................35

Reading the BMW MoDiTeC fault code memory

 .......................................................35

(Inspections I, II, III and IV) .................................................................................................................35

[Integral ABS] Perform bleed test with BMW MoDiTeC

 .........................................35

(Inspections II and III) .........................................................................................................................35

Checking throttle cable play, adjusting if necessary 

..............................................36

(Inspections I and III)  .........................................................................................................................36

[Cruise control] 

Models with cruise control.

 ...................................................................37

Throttle-opener cable, throttle-closer cable  .......................................................................................37
Cruise-control system cable ..............................................................................................................37

[Cruise control]

 Turning throttle twistgrip relative to throttle-valve shaft

 ............38

cruise-control system does not switch off  .........................................................................................38
cruise-control system cannot be set, or continually shuts down ........................................................38

Changing engine oil, replacing oil filter element 

......................................................39

(Inspections I, II, III and IV) .................................................................................................................39

Gearbox oil change 

...................................................................................................................40

(Inspection III)  ....................................................................................................................................40

Rear wheel drive oil change (every 40,000 km/24,000 miles) 

............................40

(Inspections I and III)  .........................................................................................................................40

[Integral ABS] Checking brake pads/brake discs for wear/replacing 
if necessary 

....................................................................................................................................41

(Inspections II and III)

 ......................................................................................................................41

[Integral ABS] Checking front brake pads for wear

 ........................................................41

[Integral ABS] Checking rear brake pads for wear

 .........................................................41

[Integral ABS] Checking brake discs for wear

 ..................................................................41

[Integral ABS] Replacing brake pads

 ....................................................................................42

Replacing front brake pads  ...............................................................................................................42
Replacing rear brake pads  ................................................................................................................43

[Integral ABS] Checking brake fluid level at handlebar fitting 

..........................43

(Inspections II and III)

 ......................................................................................................................43

00 Maintenance

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

KAYO MOTOR T2 Service Manual preview
T2
Brand: KAYO MOTOR Pages: 61
yasuni TUB653 Assembly Instructions Manual preview
TUB653
Brand: yasuni Pages: 8
X-lite X-803RS Safety And Instructions For Use preview
X-803RS
Brand: X-lite Pages: 136
Suzuki GSX-R600 Manual preview
GSX-R600
Brand: Suzuki Pages: 165
Fantic XX 125 Use And Maintenance Manual preview
XX 125
Brand: Fantic Pages: 153
Gilera Fuoco 500 Service Station Manual preview
Fuoco 500
Brand: Gilera Pages: 396
DYNATEK D4K-DCT Manual preview
D4K-DCT
Brand: DYNATEK Pages: 1
DYNATEK D3K7-1 Installation Instructions preview
D3K7-1
Brand: DYNATEK Pages: 3
DYNATEK D3K1-1REVD Installation And Tuning Manual preview
D3K1-1REVD
Brand: DYNATEK Pages: 2
DYNATEK DDK1-5 Installation Manual preview
DDK1-5
Brand: DYNATEK Pages: 12
hepco & becker 6302523 00 01 Manual preview
6302523 00 01
Brand: hepco & becker Pages: 3
Happy Trails HTP1-8-30 Quick Start Manual preview
HTP1-8-30
Brand: Happy Trails Pages: 2
TVS TVS XL 100 Manual preview
TVS XL 100
Brand: TVS Pages: 44
Tusk Dry Duffel Bag Instructions preview
Dry Duffel Bag
Brand: Tusk Pages: 3
IBEX 10007032 Mounting Instruction preview
10007032
Brand: IBEX Pages: 3
hepco & becker 5012527 00 01 Manual preview
5012527 00 01
Brand: hepco & becker Pages: 6
hepco & becker 42239531 00 01 Mounting Instructions preview
42239531 00 01
Brand: hepco & becker Pages: 2
hepco & becker 42152541 00 01 Manual preview
42152541 00 01
Brand: hepco & becker Pages: 3

Brands by name

Popular brands

Load more brands