manualshive.com logo in svg

BMW K 1200RS, Repair Manual

The BMW K 1200RS Repair Manual is the comprehensive guide for motorcycle enthusiasts seeking to maintain and fix their BMW K 1200RS model. This essential manual provides step-by-step instructions and detailed diagrams to aid in repairs and maintenance tasks. Download your free copy from our website, manualshive.com.

Share
Download
background image

11.1

Contents

Page

11

Technical Data 

................................................................................................................................5

Preparatory work with engine installed 

......................................................................... 11

…for removal of combined oil/water pump

 ........................................................................ 11

…for removal of timing case cover, removal of timing chain

 ...................................... 11

…for removal of cylinder head, removal of piston with conrod

 ................................. 11

…for removal of crankshaft

 ....................................................................................................... 11

…for removal of intermediate flange, removal of output shaft

 ................................... 11

…for checking valve clearances, adjusting valve clearances

 .................................... 11

Removing/installing engine 

.................................................................................................. 12

Removing engine ............................................................................................................................... 12
Installing engine  ................................................................................................................................ 12

Disassembling engine 

............................................................................................................. 13

Removing, disassembling and assembling combined oil-water pump

 ................. 13

Removing the oil/water pump  ............................................................................................................ 13
Disassembling the oil/water pump ..................................................................................................... 13
Removing slipring seal and shaft sealing ring  .................................................................................... 13
Removing the oil pressure relief valve  ................................................................................................ 13
Installing the oil pressure relief valve .................................................................................................. 13
Removing the oil pressure switch and regulating element  ................................................................. 14
Installing oil pressure switch and regulating element  .........................................................................14
Install the pump shaft with shaft sealing ring and slipring seal. .......................................................... 14
Installing water pump impeller  ........................................................................................................... 14

Removing timing chain cover

 ................................................................................................... 15

Remove the crankcase cover. ............................................................................................................ 15
Removing ignition trigger ................................................................................................................... 15
Removing cylinder head cover ........................................................................................................... 15
Removing timing case cover .............................................................................................................. 16

Removing/installing shaft sealing ring in timing case cover

 ....................................... 17

Removing shaft sealing ring from timing case cover  .......................................................................... 17
Installing shaft sealing ring in timing case cover  ................................................................................ 17

Removing the timing chain

 ....................................................................................................... 18

Removing camshaft chain sprockets  ................................................................................................. 18
Removing chain tensioner rail ............................................................................................................ 18
Removing chain guide rail  ................................................................................................................. 18
Replace the lining of the chain tensioning rail and thrust piece .......................................................... 18

11 Engine

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Cannondale MX400 Parts Catalog preview
MX400
Brand: Cannondale Pages: 61
Yamaha XVS650A Owner'S Manual preview
XVS650A
Brand: Yamaha Pages: 86
Yamaha TW125 Parts Catalog preview
TW125
Brand: Yamaha Pages: 57
Yamaha TT-R90(R) Owner'S Service Manual preview
TT-R90(R)
Brand: Yamaha Pages: 288
Yamaha TRACER 700 2020 Owner'S Manual preview
TRACER 700 2020
Brand: Yamaha Pages: 98
Yamaha QT50 Service Manual preview
QT50
Brand: Yamaha Pages: 118
Yamaha XV1700PCR Road Star Warrior Owner'S Manual preview
XV1700PCR Road Star Warrior
Brand: Yamaha Pages: 122
Yamaha YZFR1W 2007 Service Manual preview
YZFR1W 2007
Brand: Yamaha Pages: 429
Yamaha XT225C Service Manual preview
XT225C
Brand: Yamaha Pages: 427
Yamaha Moto matrix YZF-R6S Supplementary Service Manual preview
Moto matrix YZF-R6S
Brand: Yamaha Pages: 41
Öhlins YA812 Mounting Instructions preview
YA812
Brand: Öhlins Pages: 2
Öhlins YA 314 Mounting Instructions preview
YA 314
Brand: Öhlins Pages: 2
Öhlins TR 538 Mounting Instructions preview
TR 538
Brand: Öhlins Pages: 2
Öhlins ST44 Mounting Instructions preview
ST44
Brand: Öhlins Pages: 2
Öhlins SD195 Mounting Instruction preview
SD195
Brand: Öhlins Pages: 2
Öhlins SD 168 Mounting Instructions preview
SD 168
Brand: Öhlins Pages: 2
Öhlins SD 154 Mounting Instructions preview
SD 154
Brand: Öhlins Pages: 2
Öhlins RS 562 Mounting Instructions preview
RS 562
Brand: Öhlins Pages: 2

Brands by name

Popular brands

Load more brands