BMW K 1200RS Repair Manual Download

Page: 308 / 416

34.14

•

Loosen pressure modulator.

•

Apply masking tape to left side of rear frame.

Attention:

Do not bend the piping system on removal.

•

Pull pressure modulator to the left to remove,
complete with brake lines and hoses.

•

If necessary, remove sealing rings from brake
lines.

Attention:

The pressure modulator contains brake fluid.

•

Set down the pressure modulator with the con-
nections upwards.

•

Installation is the reverse of the removal proce-
dure. Pay particular attention to the following:

Note:

Always replace the seals (arrow) between the brake
lines and the pressure modulator when you replace
the pressure modulator or brake lines.

Warning:

Always replace the springs (10).
Ensure correct positioning.

•

Install 3 new springs (10).

•

Clip brake lines (1-4) into position.

•

Ensure that the springs (10) are correctly seated
on both sides.

•

Install protective caps (9).

–

Fill the brake system (

34.17).

KR340740

KR340752

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands

BMW K 1200RS, Repair Manual

Search results

Summary of Contents for K 1200RS

Reviews:

Related manuals for K 1200RS

Brands by name

Popular brands