manualshive.com logo in svg

BMW K 1200RS, Repair Manual

The BMW K 1200RS Repair Manual is the comprehensive guide for motorcycle enthusiasts seeking to maintain and fix their BMW K 1200RS model. This essential manual provides step-by-step instructions and detailed diagrams to aid in repairs and maintenance tasks. Download your free copy from our website, manualshive.com.

Share
Download
background image

61.1

Contents

Page

61

Technical Data

.................................................................................................................................3

Removing/installing battery (

a 

00.69)

................................................................................5

Removing/installing battery holder

.....................................................................................5

Removing/installing electronic equipment box

............................................................5

Wiring harness

................................................................................................................................6

View from right

..................................................................................................................................6

View from left

.....................................................................................................................................7

View from front

..................................................................................................................................8

Relay positions in electronic equipment box

.......................................................................9

Renewing left multifunction switch and clutch switch

................................................... 10

Removing/installing clutch switch....................................................................................................... 11
Removing left multifunction switch ..................................................................................................... 11

Renewing right multifunction switch and brake switch

................................................. 12

Removing brake light switch ............................................................................................................... 13
Removing/installing right multifunction switch .................................................................................... 13

Removing/installing fuse box

.................................................................................................... 14

Removing/installing power socket

.......................................................................................... 14

[Without Integral ABS]

 Removing/installing inductive signal transmitter for 

speedometer

.................................................................................................................................... 15

Renewing ABS sensor at front/rear

....................................................................................... 15

Removing/installing water temperature sensor

................................................................. 15

Replacing side stand switch

..................................................................................................... 16

Removing/installing side stand switch ................................................................................................ 16
Check operation of side stand switch (

a 

00.71) ................................................................................ 16

Renewing/adjusting foot brake light switch

........................................................................ 17

Removing/installing ignition switch/steering lock cable

............................................... 18

Removing/installing oil pressure switch/cable for temperature sensor at 
water pump

....................................................................................................................................... 19

Removing/installing oil pressure switch cable..................................................................................... 19
Removing/installing temperature sensor at water pump...................................................................... 19

Removing/installing horn

............................................................................................................20

61 General electrical equipment

Summary of Contents for K 1200RS

































































































































































































































































































































































































































Reviews:

No comments

Related manuals for K 1200RS

Öhlins YA 559 Mounting Instructions preview
YA 559
Brand: Öhlins Pages: 8
KEDO 31118MR Quick Start Manual preview
31118MR
Brand: KEDO Pages: 2
KEDO 60520R Manual preview
60520R
Brand: KEDO Pages: 3
KEDO 31103 Manual preview
31103
Brand: KEDO Pages: 2
GYS 037281 User Manual preview
037281
Brand: GYS Pages: 36
HERO ACHIEVER 150 Manual preview
ACHIEVER 150
Brand: HERO Pages: 68
Honda ADV150A User Manual preview
ADV150A
Brand: Honda Pages: 4
hepco & becker 5039505 00 01 Quick Start Manual preview
5039505 00 01
Brand: hepco & becker Pages: 2
DYNATEK DDK7-1 Installation Manual preview
DDK7-1
Brand: DYNATEK Pages: 8
Honeywell PA810EU User Instructions preview
PA810EU
Brand: Honeywell Pages: 93
Husqvarna 28512027000 Information preview
28512027000
Brand: Husqvarna Pages: 12
Husqvarna 27035936044 Information preview
27035936044
Brand: Husqvarna Pages: 12
Husqvarna 28012979044 Information preview
28012979044
Brand: Husqvarna Pages: 7
Husqvarna 28508915044 Information preview
28508915044
Brand: Husqvarna Pages: 32
Husqvarna 9301395014430 Information preview
9301395014430
Brand: Husqvarna Pages: 7
Husqvarna H300 Product User Manual preview
H300
Brand: Husqvarna Pages: 128
hepco & becker 6304522 black Assembling Instructions preview
6304522 black
Brand: hepco & becker Pages: 6
Yamaha 1990 FZR1000 Assembly Manual preview
1990 FZR1000
Brand: Yamaha Pages: 5

Brands by name

Popular brands

Load more brands